4 pin aviation reversing camera

Black Reversing Camera - Sony CCD 700TVL - Stainless Steel Bracket - 4-Pin

£68.00

VAT Included £11.33

White Motorhome Reversing Camera - Sony CCD 700TVL - Stainless Steel Bracket - 4-Pin

Great Image Quality thanks to the Sony 1/3" CCD Image Sensor Fitted - The Sony 811 1/3" CCD image sensor has long been our favourite image sensor for reversing cameras. The image sensor is the part of the camera responsible for producing an image, so as you can imagine, it plays a massive part in the image quality you see.
Flexible Mounting Bracket - Bracket cameras remain one of the most popular types for mounting on vehicles as a reversing camera. They are easy to fit and can be mounted in a position of your choice. Most commonly, these are mounted higher up, sometimes on a rear vertical wall, e.g. on the back of a Motorhome or Van, and sometimes on a horizontal surface, e.g. on the top of a door/roof.
IR Night Vision LED's - Thanks to the 18 IR LEDs and the great low light sensitivity of the installed Sony 811 1/3" CCD sensor, you can expect great night vision. Really important to illuminate the area behind the vehicle for the camera to help you see hazards/obstacles. Don't worry about the light affecting following drivers as it is invisible to the human eye - the camera sees and uses it.
IP68 Waterproof Protection - This camera is built to thrive in bad weather. The IP rating gives an "ingress protection" rating against dust and water. IP68 is very high and means that it can survive in the worst storms the Great British weather can throw at it.
Mirror Image for Rear View / Reversing - The reversing camera will send a mirror image to the monitor. This is essential for cameras pointing backwards, to ensure that the obstacles on your left are displayed to the left of the display - like a mirror does.
Rust Resistant Painted Stainless Steel Bracket - There's nothing worse than having a rusty, mild steel reversing camera leaving orange streaks down the back of your pride and joy Motorhome. We have seen other supplier's cameras with such rusty brackets that the camera is no longer supported. No such worry with this camera. This camera uses a rust-resistant stainless steel bracket painted with matt black paint. Time tested and proven to look great many, many years later.
120°Wide Viewing Angle - The camera has a nice wide viewing angle to help give maximum coverage and help to avoid obstacles behind the vehicle.
Added Reversing Safety - Most importantly, with almost a quarter of all vehicle accidents in the UK occurring when reversing, having a good quality reversing camera providing a nice, clear image for the driver to view whilst reversing will reduce the likelihood of vehicle damage or harm to others.
4 Pin Waterproof Screw Connector - We have been a fan of the 4 pin aviation screw connector since the early 2000's. We quickly decided to build up all of our range of reversing camera kits with this type of connector. Some of our competitors chose to use inferior proprietary connectors in an attempt to lock people in to buying overpriced replacements from them. We chose a universally wired-up connector and chose the business model of selling high-quality, high-specification products for the lowest price possible.

£68.00

VAT Included £11.33

Silver Reverse Parking Camera - Sony CCD 700TVL - Stainless Steel Bracket - 4-Pin

Great Image Quality thanks to the Sony 1/3" CCD Image Sensor Fitted - The Sony 811 1/3" CCD image sensor has long been our favourite image sensor for reversing cameras. The image sensor is the part of the camera responsible for producing an image, so as you can imagine, it plays a massive part in the image quality you see.
Flexible Mounting Bracket - Bracket cameras remain one of the most popular types for mounting on vehicles as a reversing camera. They are easy to fit and can be mounted in a position of your choice. Most commonly, these are mounted higher up, sometimes on a rear vertical wall, e.g. on the back of a Motorhome or Van, and sometimes on a horizontal surface, e.g. on the top of a door/roof.
Rust Resistant Painted Stainless Steel Bracket - There's nothing worse than having a rusty, mild steel reversing camera leaving orange streaks down the back of your vehicle. We have seen other supplier's cameras with such rusty brackets that the camera is no longer supported. No such worry with this camera. This camera uses a rust-resistant stainless steel bracket painted with attractive silver paint. Time tested and proven to look great many, many years later.
IR Night Vision LED's - Thanks to the 18 IR LEDs and the great low light sensitivity of the installed Sony 811 1/3" CCD sensor, you can expect great night vision. Really important to illuminate the area behind the vehicle for the camera to help you see hazards/obstacles. Don't worry about the light affecting following drivers as it is invisible to the human eye - the camera sees and uses it.
IP68 Waterproof Protection - This camera is built to thrive in bad weather. The IP rating gives an "ingress protection" rating against dust and water. IP68 is very high and means that it can survive in the worst storms the Great British weather can throw at it.
Mirror Image for Rear View / Reversing - The reversing camera will send a mirror image to the monitor. This is essential for cameras pointing backwards, to ensure that the obstacles on your left are displayed to the left of the display - like a mirror does.
Built-in Microphone - Sometimes we have customers who have a requirement for a microphone to be fitted, usually so they can hear directions from people to the rear of the vehicle.
120°Wide Viewing Angle - The camera has a nice wide viewing angle to help give maximum coverage and help to avoid obstacles behind the vehicle.
Added Reversing Safety - Most importantly, with almost a quarter of all vehicle accidents in the UK occurring when reversing, having a good quality reversing camera providing a nice, clear image for the driver to view whilst reversing will reduce the likelihood of vehicle damage or harm to others.
4 Pin Waterproof Screw Connector - We have been a fan of the 4 pin aviation screw connector since the early 2000's. We quickly decided to build up all of our range of reversing camera kits with this type of connector. Some of our competitors chose to use inferior proprietary connectors in an attempt to lock people in to buying overpriced replacements from them. We chose a universally wired-up connector and chose the business model of selling high-quality, high-specification products for the lowest price possible.

£68.00

VAT Included £11.33

Black Twin-Lens Reversing & Rear-View Camera - Sony CCD 700TVL - Stainless Steel Bracket - 4-Pin

Two Cameras In One Bracket - The twin lens reversing camera is actually two individual cameras that mount to the same painted stainless steel bracket.
Narrow-Angle for Rear View + Wide Angle for Parking - Different lens angles for different functions. The narrow-angle lens is suited for always-on rear view driving cameras - as the distance perception is less distorted than a wider angle lens. The 8mm fitted long-distance lens performs brilliantly when monitoring traffic driving behind your vehicle. The wide-angle lens in the downward-facing reversing camera works brilliantly to give a big spread behind to allow you to see hazards.
Anti-Rust Stainless Steel Bracket - We have been using stainless steel brackets on most of our bracket cameras since the early 2010's. Ever since the upgrade we have never had a customer request a new bracket to replace a rusty one. With non-stainless steel people sometimes see rusting occur within as little as 2 weeks. We believe you shouldn't have to suffer unattractive rusty brackets on the back of your vehicle, with the associated orange streaks running down.
Always On Functionality and Safety - The twin/dual lens cameras are designed to be on for the entire journey, improving your visibility/safety 100% of the journey vs the 1 or 2% of the time you are in reverse.
Sony 700tvl CCD Image Sensors - The Sony 811 960H 700tvl Image Sensors fitted to BOTH cameras provide a high-resolution image with excellent colour replication in the day and good night vision in the dark.
Popular for Vans and Motorhomes - This type of camera is most popular with van and motorhome owners who often have poor visibility to the rear when driving. This setup gives them an amazing rear view mirror view, as well as showing them the rear of their vehicles when reversing to avoid hitting anything.
Night Vision IR LED's - The cameras have IR LED's fitted to allow the camera to see in the dark. No need to worry about this disturbing following vehicles since the Infra Red Light they emit is below the visible spectrum of the human eye. This means you get a great night vision image on your display and people behind you don't suffer any glare from a light.
IP68 Waterproof - These cameras are rated at IP68, which means they are protected against the very worst of the Great British weather.
Small Entry Hole Size Disconnect Points (Optional to Remove when Ordering) - As standard we will provide the camera with small 8mm disconnect points to allow for smaller hole size for cable entry. These smaller disconnects aren't waterproof, so if you can't get them inside the body of your vehicle within 30cm please select the non-8mm version option above.

£130.00

VAT Included £21.67

White Twin-Lens Reversing & Rear-View Camera for Motorhome - Sony CCD 700TVL - Stainless Steel Bracket - 4-Pin

Two Cameras In One Bracket - The twin lens reversing camera is actually two individual cameras that mount to the same painted stainless steel bracket.
Narrow-Angle for Rear View + Wide Angle for Parking - Different lens angles for different functions. The narrow-angle lens is suited for always-on rear view driving cameras - as the distance perception is less distorted than a wider angle lens. The 8mm fitted long-distance lens performs brilliantly when monitoring traffic driving behind your vehicle. The wide-angle lens in the downward-facing reversing camera works brilliantly to give a big spread behind to allow you to see hazards.
Anti-Rust Stainless Steel Bracket - We have been using stainless steel brackets on most of our bracket cameras since the early 2010's. Ever since the upgrade we have never had a customer request a new bracket to replace a rusty one. With non-stainless steel people sometimes see rusting occur within as little as 2 weeks. We believe you shouldn't have to suffer unattractive rusty brackets on the back of your vehicle, with the associated orange streaks running down.
Always On Functionality and Safety - The twin/dual lens cameras are designed to be on for the entire journey, improving your visibility/safety 100% of the journey vs the 1 or 2% of the time you are in reverse.
Sony 700tvl CCD Image Sensors - The Sony 811 960H 700tvl Image Sensors fitted to BOTH cameras provide a high-resolution image with excellent colour replication in the day and good night vision in the dark.
Popular for Vans and Motorhomes - This type of camera is most popular with van and motorhome owners who often have poor visibility to the rear when driving. This setup gives them an amazing rearview mirror view, as well as showing them the rear of their vehicles when reversing to avoid hitting anything.
Night Vision IR LED's - The cameras have IR LED's fitted to allow the camera to see in the dark. No need to worry about this disturbing following vehicles since the Infra Red Light they emit is below the visible spectrum of the human eye. This means you get a great night vision image on your display and people behind you don't suffer any glare from a light.
IP68 Waterproof - These cameras are rated at IP68, which means they are protected against the very worst of the Great British weather.
Small Entry Hole Size Disconnect Points (Optional to Remove when Ordering) - As standard we will provide the camera with small 8mm disconnect points to allow for smaller hole size for cable entry. These smaller disconnects aren't waterproof, so if you can't get them inside the body of your vehicle within 30cm please select the non-8mm version option above.

£130.00

VAT Included £21.67

Polished Stainless Steel Reversing Camera - Sharp CCD 600TVL - 4-Pin

£108.00

VAT Included £18.00

Numberplate Frame Reversing Camera - 600TVL - 4-Pin

Excellent Image Quality - Thanks to the high-quality modern PC1058 600tvl high-resolution image sensor installed, coupled with an excellent Aspheric lens you can expect a sharp, clear image, with good colour replication.
IP69K Waterproof - With the highest standard in water ingress protection, this reversing camera is sure to withstand anything the Great British weather chooses to unleash on it. Similar looking cameras tend to fill auto electricians with a sense of dread, as similar barrel based cameras have an awful reputation for leaking. Not this one! These cameras have been impeccable.
Extra Durable and Reliable - Not to be confused with cheaper imitations. This model comes from one of our best rated manufacturers for reversing cameras. Fitting one of these cameras to your vehicle will give you trouble-free ownership.Adjustable Tilt Angle - There are two small screws to the front of the camera, which when turned anti-clockwise allows the camera barrel to rotate up/down. Once you have the perfect view, simply tighten back up to lock. The camera barrel can even be removed and refitted upside down, so that the camera can be at the bottom of the number plate instead of the top.
Night Vision IR LED's - It is unusual for a numberplate camera to have night vision, this camera is fitted with 4x high powered Infra Red LED's, which provides the camera with light to keep you safe at night time. The light is invisible to the human eye, so no worries about blinding following traffic.
Built In Microphone - The camera is fitted with a microphone, which may be useful to some customers who want to hear instructions from people close to the camera. Please be aware that to hear the microphone, you need to ensure that your Monitor has a built-in speaker.
Extra Wide Aspheric Lens - 150 degrees field of view, without the fish bowl effect, thanks to the really high quality Aspheric lens installed in this reverse camera.
4 Pin Connector / Optional RCA Phono Adaptors - The camera uses the most popular 4 pin screw connector to take Video Signal, Audio from the microphone, and Power. Should you wish to convert this to RCA Phono Connection e.g. for an RCA Monitor or Stereo Headunit e.g. Sony/Kenwood/Pioneer you can order a discounted bundle set which has our 4 pin to RCA Adaptor + Power Wire with inline fuse + RCA Coupler.
Easy to Fit - One of the most widely reported feedback we get from customers about this camera is that it is so easy to fix to the vehicle thanks to it re-using the original fixings for the numberplate. Check out our video below to see what is involved in fitting.

£90.00

VAT Included £15.00

Numberplate Reversing Camera - 600TVL - 4-Pin

Great Image Quality - With the modern premium PC1058 image sensor combined with the high-quality Aspheric lens, the image this reversing camera produces is really impressive. It will produce a decent image day and night.
Extra Wide Angle Quality Aspheric Lens - This camera has a built-in 150 degree Aspheric Lens. This means you get a very sharp and clear image, which is also very wide, yet doesn't look like you are looking out of a fishbowl.
Superb Build Quality - This style of reversing camera traditionally has a bad reputation. When I show auto electricians who visit us and suggest this one, they are filled with dread as most similar-looking cameras sold elsewhere are likely to leak. After I assure them that ours is entirely different and they try them out, it becomes a favourite.
Adjustable Tilt - You can rotate and lock the adjustment of the camera. This means you can obtain the optimum viewing angle to get the most out of your reverse camera.
IP69K Waterproof Rating - With the highest water and dust ingress protection rating that you can get, rest assured this camera will cope with the worst weather you can imagine.
Flexible Mounting Location - Designed so that it can either be mounted on a vertical surface e.g. rear wall, or a horizontal surface e.g. underneath number plate light trim/cross bar. The barrel camera inside the camera housing can be removed and spun/upside down to ensure the camera image is always the correct way up.
Night Vision IR LED's - Number Plate cameras rarely have night vision IR LED's. This camera does! The IR LED's light up the area for the camera to see when there is a low light level. No need to worry about the light blinding following drivers because IR Infra Red light is invisible to the human eye - only the camera will see it.
Microphone - This reversing camera has an inbuilt microphone. This is sometimes useful for people who install the camera on a monitor with a built-in speaker.
4 Pin Connector / Optional RCA Phono Adaptors - The camera uses the most popular 4 pin screw connector to take Video Signal, Audio from the microphone, and Power. Should you wish to convert this to RCA Phono Connection e.g. for an RCA Monitor or Stereo Headunit e.g. Sony/Kenwood/Pioneer you can order a discounted bundle set which has our 4 pin to RCA Adaptor + Power Wire with inline fuse + RCA Coupler.