Reversing Cameras

This is one of the latest cameras on the market that bypass the problem of lipped doors which mean you can't fit a traditional bracket camera above the doors. This allows you to have a birds eye view still on lots of the modern vans.

This is one of the latest cameras on the market that bypass the problem of lipped doors which mean you can't fit a traditional bracket camera above the doors. This allows you to have a birds eye view still on lots of the modern vans.
 

This is usually used as a side camera, and is fitted with a top spec 1/3" Sony CCD 700TVL image sensor.

This is our compact side mounting blind spot elimination camera. It can be fitted to either side of the vehicle, or even used on the back as a downward facing reversing camera. The ball camera can be rotated and adjusted out slightly, making it flexible enough for all of these fitting positions.

This is usually used as a side camera.

This is usually used as a side camera.

This is a new camera which will clamp on to most tubes whether it be side mirror tubes or bike racks.

You may recognise this camera from a very expensive branded system, that's because we used the same factory to import it from except we had the very latest 600TVL 1/3" Sharp CCD (not to be confused with the older 420TVL 1/3" Sharp CCD).  We would say this new image sensor is on par with the Sony 700TVL we use in our other high end cameras.  This camera has a nice polished Stainless Steel Bracket with a grey/silver painted main body. 

We have stocked a twin lens camera for more than a decade that uses two cameras with a compact 50mm width case. Because we frequently get asked by customers if they can use just the one in a small bracket, and because we like to listen and learn from customers, we decided to get a bracket specially produced to house our large selection of twin lens camera units. Choice of lens angle for either parking view (120 degrees) or rear view (45 degrees). The camera body is painted white, whilst the bracket is polished stainless steel. The image sensor fitted is Sony's 811, which is our favourite sensor - 1/3" CCD 700tvl.

We have stocked a twin lens camera for more than a decade that uses two cameras with a compact 50mm width case. Because we frequently get asked by customers if they can use just the one in a small bracket, and because we like to listen and learn from customers, we decided to get a bracket specially produced to house our large selection of twin lens camera units. Choice of lens angle for either parking view (120 degrees) or rear view (45 degrees). The camera body is painted black, whilst the bracket is polished stainless steel. The image sensor fitted is Sony's 811, which is our favourite sensor - 1/3" CCD 700tvl.

We get asked by some people for a camera they can make normal view instead of mirror (perhaps as an internal camera or a camera looking forwards or to the side).  Although we wouldn't recommend it low down looking forwards due to the risk of stone chips.

Our Black Painted Stainless Steel Bracket Rear View / Driving Camera is fitted with a Sony 1/3" CCD 700tvl image sensor for a great, colourful, high-resolution image. Fitted with 18 IR LEDs and with the Sony 811's great low-light level sensitivity, this camera has excellent night vision. Thanks to the painted stainless steel bracket, an excellent rust-resistant material, there are no worries regarding rusty brackets. 4 Pin waterproof screw locking connector cable, with the option to add one of our RCA adaptor bundle sets should you have an RCA Monitor or are fitting to a Stereo head unit.
 

Our White Painted Stainless Steel Bracket Rear View / Driving Camera is fitted with a Sony 1/3" CCD 700tvl image sensor for a great, colourful, high-resolution image. Fitted with 18 IR LEDs and with the Sony 811's great low-light level sensitivity, this camera has excellent night vision. Thanks to the painted stainless steel bracket, an excellent rust-resistant material, there are no worries regarding rusty brackets. 4 Pin waterproof screw locking connector cable, with the option to add one of our RCA adaptor bundle sets should you have an RCA Monitor or are fitting to a Stereo head unit.
 

This is an updated version of the roof mounted overhang reverse camera.  This version has an added rear view camera as a permanent on driving aid.

This is the phono / RCA version of our popular dome reversing camera.  Fitted with a 1/3" Sony CCD 700TVL sensor for a great image both day and night.

Cable length of 5-20M can be selected inside listing. These cameras come with the 1/3" Sony CCD sensor and give a very good image.

This is the phono / RCA version of our popular dome reversing camera.  Fitted with a 1/3" Sony CCD 700TVL sensor for a great image both day and night.

White painted stainless steel bracket reversing camera to suit motorhomes/caravans/vans

High resolution CCD camera, with infrared illumination at night, waterproof, 12 month guarantee and a 5m RCA video cable. The important thing about CCD cameras is they give a much better image than the cheaper CMOS versions. Cable length of 5-20M can be selected inside listing.
 

• Two Cameras In One Bracket - The twin lens reversing camera is actually two individual cameras that mount to the same painted stainless steel bracket.
• Narrow-Angle for Rear View + Wide Angle for Parking - Different lens angles for different functions. The narrow-angle lens is suited for always-on rear view driving cameras - as the distance perception is less distorted than a wider angle lens. The 8mm fitted long-distance lens performs brilliantly when monitoring traffic driving behind your vehicle. The wide-angle lens in the downward-facing reversing camera works brilliantly to give a big spread behind to allow you to see hazards.
• Anti-Rust Stainless Steel Bracket - We have been using stainless steel brackets on most of our bracket cameras since the early 2010's. Ever since the upgrade we have never had a customer request a new bracket to replace a rusty one. With non-stainless steel people sometimes see rusting occur within as little as 2 weeks. We believe you shouldn't have to suffer unattractive rusty brackets on the back of your vehicle, with the associated orange streaks running down.
• Always On Functionality and Safety - The twin/dual lens cameras are designed to be on for the entire journey, improving your visibility/safety 100% of the journey vs the 1 or 2% of the time you are in reverse.
• Sony 700tvl CCD Image Sensors - The Sony 811 960H 700tvl Image Sensors fitted to BOTH cameras provide a high-resolution image with excellent colour replication in the day and good night vision in the dark.
• Popular for Vans and Motorhomes - This type of camera is most popular with van and motorhome owners who often have poor visibility to the rear when driving. This setup gives them an amazing rear view mirror view, as well as showing them the rear of their vehicles when reversing to avoid hitting anything.
• Night Vision IR LED's - The cameras have IR LED's fitted to allow the camera to see in the dark. No need to worry about this disturbing following vehicles since the Infra Red Light they emit is below the visible spectrum of the human eye. This means you get a great night vision image on your display and people behind you don't suffer any glare from a light.
• IP68 Waterproof - These cameras are rated at IP68, which means they are protected against the very worst of the Great British weather.

• Two Cameras In One Bracket - The twin lens reversing camera is actually two individual cameras that mount to the same painted stainless steel bracket.
• Narrow-Angle for Rear View + Wide Angle for Parking - Different lens angles for different functions. The narrow-angle lens is suited for always-on rear view driving cameras - as the distance perception is less distorted than a wider angle lens. The 8mm fitted long-distance lens performs brilliantly when monitoring traffic driving behind your vehicle. The wide-angle lens in the downward-facing reversing camera works brilliantly to give a big spread behind to allow you to see hazards.
• Anti-Rust Stainless Steel Bracket - We have been using stainless steel brackets on most of our bracket cameras since the early 2010's. Ever since the upgrade we have never had a customer request a new bracket to replace a rusty one. With non-stainless steel people sometimes see rusting occur within as little as 2 weeks. We believe you shouldn't have to suffer unattractive rusty brackets on the back of your vehicle, with the associated orange streaks running down.
• Always On Functionality and Safety - The twin/dual lens cameras are designed to be on for the entire journey, improving your visibility/safety 100% of the journey vs the 1 or 2% of the time you are in reverse.
• Sony 700tvl CCD Image Sensors - The Sony 811 960H 700tvl Image Sensors fitted to BOTH cameras provide a high-resolution image with excellent colour replication in the day and good night vision in the dark.
• Popular for Vans and Motorhomes - This type of camera is most popular with van and motorhome owners who often have poor visibility to the rear when driving. This setup gives them an amazing rearview mirror view, as well as showing them the rear of their vehicles when reversing to avoid hitting anything.
• Night Vision IR LED's - The cameras have IR LED's fitted to allow the camera to see in the dark. No need to worry about this disturbing following vehicles since the Infra Red Light they emit is below the visible spectrum of the human eye. This means you get a great night vision image on your display and people behind you don't suffer any glare from a light.
• IP68 Waterproof - These cameras are rated at IP68, which means they are protected against the very worst of the Great British weather.
• Small Entry Hole Size Disconnect Points (Optional to Remove when Ordering) - As standard we will provide the camera with small 8mm disconnect points to allow for smaller hole size for cable entry. These smaller disconnects aren't waterproof, so if you can't get them inside the body of your vehicle within 30cm please select the non-8mm version option above.

This is the bolt version number plate reverse camera.  Simply drill a small hole on the underside of your number plate ledge for the bolt of the camera to fit through.  Then fasten to vehicle with the special split type nut provided.  The result is a very small camera that is quite hard to even see!  We have had this made by the same factory that makes our upgraded brake light cameras.  Using their high quality PC4089 700TVL sensor and fully glass composite lens combination.  

This is one of our latest cameras in, we wanted to add a small flexible camera to our range, with a high resolution.  We asked for these cameras to be made with the PC4089 image sensor - the same sensor we use in our brake light cameras, we spent extra to spec the cameras out with 4 glass lenses, instead of the standard 2 glass/2 plastic that you would usually see on these type of cameras (we chose all glass lenses because the plastic lenses go cloudy over time, because of UV exposure from the sun).  The PC4089 image sensor is one of the modern latest generation of CMOS (not to be confused with the cheap and cheerful CMOS of the past).  As the price is lower than CCD, we have passed these savings on to you. 

We used to stock a similar reversing camera many years ago.  When we found this one, which had the higher quality image sensor options available we gladly ordered some.  These were always a popular, easy to fit option for people wanting a small, discreet camera.  The actual camera part itself is only 22mm deep and 18mm in height, it is attached to a bracket that is mostly hidden behind the numberplate itself.  You have the option of using screws to attach this, or my preference is either an adhesive sealant, or some very strong tape such as Scotch Red.