Products Map

• Our 12.5M length 4 pin top quality extension cable for reversing cameras. 
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is suitable for the latest range of 1080P AHD reversing cameras.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 12.5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

We prefer adhesive lined heat shrink versus non adhesive lined. The added advantages are that the connection is moistureproof and the heatshrink will never move position to expose the wires underneath.

99% of the time, if you see a DC socket on a reversing camera or monitor, it will be a 2.1mm/5.5mm connector.  This wire allows you to provide power to this type of socket, and has an inline 3 amp fuse on the red input wire. Total length of this power adaptor is 150CM.

• Our 15M length 4 pin top quality extension cable for reversing cameras. 
• This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs. 
• Fully waterproof connection to camera, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is suitable for the latest range of 1080P AHD reversing cameras.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 15M length 4 pin top quality extension cable for reversing cameras. 
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is suitable for the latest range of 1080P AHD reversing cameras.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

If you see a DC power socket on a reversing camera or a monitor, probably around 99% of the time this will be a 2.1mm/5.5mm DC socket. In some circumstances you may wish to extend this cable, for example when you wish to run an RCA/Phono based camera whilst driving by taking an ignition based power supply from the front of the vehicle back to the reversing camera. This is our shorter length cables at 1500cm (15M) version.

This is our 15M Extension Video RCA Phono video lead for reverse parking cameras.  It is a heavy duty thick diameter cable. 

This is our 15M (1500cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.

This is a nice simple heat gun, supplied with 5 directional hot air flow nozzles. Our customers use this when heat shrinking the connections - either some tube heat shrink over a solder joint, or one of the new solder seal wire connectors.

We prefer adhesive lined heat shrink versus non adhesive lined. The added advantages are that the connection is moistureproof and the heatshrink will never move position to expose the wires underneath.

• Our 1M length 4 pin top quality extension cable for reversing cameras. 
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is suitable for the latest range of 1080P AHD reversing cameras.
• This cable is sometimes known as a 4 pin aviation connector cable.

This is a 2 way heavy duty trailer link, using the 13 pin Euro connector, which is a 90 degree twist lock design.  Simply choose the 4 pin extension cables you require from here: 4 Pin Cables

If you have a requirement to have two cameras on your trailer, and need a flexible heavy duty suzie coil then you have found the right product.  Each side has 30cm tails, simply add your cable length of choice from the 4 pin cable category.

We get asked repeatedly for a simple, low cost mobile DVR recorder to record 1 or 2 reverse / side cameras. This can be used to record our non-AHD reversing and side cameras.  The footage will be recorded in D1 quality.

This cable allows you to have 2x reversing cameras on a trailer/caravan, connected up via cable to the towing vehicle.  Simply choose the 4 pin cables you require from here: 4 Pin Cables

Sometimes you wish to split one power supply cable so that it powers two separate devices eg a monitor and an MDVR, or two phono/RCA based reversing cameras. This cable allows you to do so.

We had these made up so that they would plug in to the 2.1mm DC sockets that are on most of our monitor wiring harnesses.  Fuse taps are a convenient way to tap into a power supply for your new camera system.

We had these made up so that they would plug in to the 2.1mm DC sockets that are on most of our monitor wiring harnesses.  Fuse taps are a convenient way to tap into a power supply for your new camera system.

• Our 20M length 4 pin top quality extension cable for reversing cameras. 
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is suitable for the latest range of 1080P AHD reversing cameras.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 20M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

This is our 15M (1500cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.