Cables, Adaptors, Tools and Fixings

• Our 5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 10M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 10M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 12.5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 12.5M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 15M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• This version comes with a small 8mm diameter disconnect link point 100cm back from the connector at the front of the cable. This was placed there so that the larger 15mm diameter connector could be unplugged (to get through tight gaps) and then reconnected once you arrive close to your monitors channel inputs.
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside. Please note that the 8mm disconnect link isn't waterproof, so will need to be inside (as this is placed at the front of the cable, this part is usually next to the monitor and isn't an issue).
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

• Our 20M length two channel/signal 4 pin top quality extension cable for reversing cameras. 
• We call these Y cables, since the shape of the ends look like the letter Y, as they are a single cable to make running cables easier, but then split to two male connectors for the reversing/rear view cameras, and two female connectors to feed a monitor.
• Fully waterproof connection, comes with screw locking collar that compresses the connection against the rubber O ring inside.
• Our extension cables are made from pure copper (not the cheaper CCA/CCS which is prone to failure).
• The cable has screening around the video signal wire, as well as aluminium foil around covering all of the wires inside the cable - to protect against outside interference, as well as allowing you to coil up any excess cable.
• This cable is not suitable for the latest range of 1080P AHD reversing cameras (although we have developed a version of this cable that is currently being produced that will be). Our single channel cables will support the high frequency AHD cameras until we get the new design twin cables delivered.
• This cable is sometimes known as a 4 pin aviation connector cable.

We were repeatedly asked by people who like the small compact size of each of the twin reversing camera units, and who wished for a bracket that could house one separately in situations where they do not need both eg they have a reversing camera, but would like to use the narrow angle rear view camera by itself. This product is the answer. Polished stainless steel to prevent rust. Stainless steel fixings, and nylon washers included in the most common screw size required for this type of camera.

Ever since we moved to painted stainless steel brackets for most of our bracket cameras more than a decade ago, we have been asked by people who have bought elsewhere if they can buy one of our spare stainless steel brackets to replace their rusted mild steel ones. This listing allows you to purchase the bracket by itself without having to purchase a whole new camera. This version is painted in black.

Ever since we moved to painted stainless steel brackets for most of our bracket cameras more than a decade ago, we have been asked by people who have bought elsewhere if they can buy one of our spare stainless steel brackets to replace their rusted mild steel ones. This listing allows you to purchase the bracket by itself without having to purchase a whole new camera. This version is painted in white.

We often get asked by our customers for a more simple trailer connector without double sockets and flexible suzi coils, this is it.  The side with the waterproof flap sits on the towing vehicle side, the side with the plug will remain on the trailer side (this will need protecting from rain when not connected).  Each side has 100cm tails, simply add your cable length of choice from the 4 pin cable category.

This is the second version of our Heavy Duty Trailer Link, the cost of these cables increased a few years back so we introduced this version for people looking for a cheaper option.  As the V1 and V2 don't fit together we have two separate listings, we have kept the more expensive version 1's in stock to allow existing customers to add on to their existing fleet.  If you haven't used any of our links before and price is a factor then this V2 version will probably be the best option.  I will add that the more expensive V1 in the other listing does "feel" more robust, having said that the V2 has had no problems with durability in the years we've ran with them.  

This is the original version of our Heavy Duty Trailer Link, the cost of these increased a few years back so we have introduced another listing (V2) for people looking for a cheaper option.  As the V1 and V2 don't fit together we have two separate listings, we have kept the more expensive version 1's in stock to allow existing customers to add on to their existing fleet.  If you haven't used any of our links before and price is a factor then the V2 might be a better option.  I will add that the more expensive V1 in this listing does "feel" more robust, having said that the V2 has had no problems with durability in the years we've ran with them.  

• This plug and socket set is suitable for use with our reversing camera systems that use the 4 pin aviation connectors. 
• It is our standard model often used for agricultural purposes, as well as being suitable for use on trailers and caravans. 
• The coil is 0.8m long and stretches to 1.6m easily (measurements approximate). 
• When connected it forms a locked waterproof join. Each socket has a spring loaded cover to keep moisture out when not in use. 
• The set carries the signal from one reversing camera. 
• If you have an articulated HGV we recommend one of our heavy duty trailer links - which allows a longer extension with the flexible coil.

To get the desired length of cable, simply add any of our 4 pin extension cables.

If you have a requirement to have two cameras on your trailer, and need a flexible heavy duty suzie coil then you have found the right product.  Each side has 30cm tails, simply add your cable length of choice from the 4 pin cable category.

This is a 2 way heavy duty trailer link, using the 13 pin Euro connector, which is a 90 degree twist lock design.  Simply choose the 4 pin extension cables you require from here: 4 Pin Cables

This cable allows you to have 2x reversing cameras on a trailer/caravan, connected up via cable to the towing vehicle.  Simply choose the 4 pin cables you require from here: 4 Pin Cables

This cable allows you to have 3 cameras go across to the trailer/caravan.  Simply choose the 4 pin cables you require from here: 4 Pin Cables

This cable allows you to have 4 cameras go across to the trailer/caravan.  Simply choose the 4 pin cables you require from here: 4 Pin Cables

We have been keeping these trailer link connection plug and socket sets in stock for our customers who want to create their own custom trailer link connections. These are the same plugs and sockets that we use in our standard duty trailer links. If you are building a connection for a single camera, then the 5-pin version would be the best option. However, if you require multiple connections, then the 7-pin version would be necessary.

This is our 5M Extension Video RCA Phono video lead for reverse parking cameras.  It is a heavy duty thick diameter cable. 

This is our 6M (600cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.

This is our 10M Extension Video RCA Phono video lead for reverse parking cameras.  It is a heavy duty thick diameter cable. 

This is our 10M (1000cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.

This is our 15M Extension Video RCA Phono video lead for reverse parking cameras.  It is a heavy duty thick diameter cable. 

This is our 15M (1500cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.

This is our 20M Extension Video RCA Phono video lead for reverse parking cameras.  It is a heavy duty thick diameter cable. 

This is our 15M (1500cm) version of the RCA Phono extension cable with built in "trigger wire".  You will notice that there is a small red wire coming out of the end of both ends of this cable.  This is an additional wire that we have had installed, designed so that you can send a reverse light trigger supply to your monitor - telling it when you are in reverse gear.  We have also seen people use this spare wire to send power from an ignition source at the front of the vehicle to the red power wire for the reversing camera.

There are times when people find themselves with two male phono / RCA plugs that they need to join together. These female to female couplers help to overcome this and "couple" the two plugs together.

There may be occasions where you need to connect two female RCA Phono connectors together.  This gender changer allows you to do so.

ACC093 - BNC Plug to RCA Phono (Female)

These are easy to use, reusable, and gentle on the cables being tied up. We like these cable ties. 

We don't usually recommend cable ties for securing cables, but if you are using conduit, or you add some protection between the cable tie and the cable then these are ideal. They measure 250mm length by 4.6mm width.

We don't usually recommend cable ties for securing cables, but if you are using conduit, or you add some protection between the cable tie and the cable then these are ideal. 

This is a bundle that contains 10 each of the black 19mm x 19mm adhesive cable tie base and 250mm length cable ties.  They fit well together.

We don't usually recommend cable ties for securing cables, but if you are using conduit, or you add some protection between the cable tie and the cable then these are ideal. This is the black version, we also stock white. We sell these in multiples of 10 pieces.