Cables, Adaptors, Tools and Fixings

• Compatible replacement for selected Dometic reversing cameras (e.g. CAM45, CAM50)
• Includes black Sony CCD bracket camera + 6-pin screw-lock adaptor
• Plug-and-play installation with matched pin configuration
• Superior picture quality and durability vs original cameras
• 2-year UK warranty included

• Compatible replacement for selected Dometic reversing cameras (e.g. CAM45, CAM50)
• Includes white compact Sony CCD bracket camera + 6-pin screw-lock adaptor
• Plug-and-play installation with matched pin configuration
• Superior picture quality and durability vs original cameras
• 2-year UK warranty included

• Compatible replacement for selected Dometic reversing cameras (e.g. CAM45, CAM50)
• Includes white Sony CCD bracket camera + 6-pin screw-lock adaptor
• Plug-and-play installation with matched pin configuration
• Superior picture quality and durability vs original cameras
• 2-year UK warranty included

These cable adaptors will convert the 2010 onwards Waeco cable fitted on vehicles like Baileys to a single 4 pin socket/plug like we use on our single camera systems. Both front and rear adaptors are provided. These cables are not made by Waeco, just compatible.  We only sell these as pairs because we have found the inside of the cables to be wired in differently.

These cable adaptors will convert the 2010 onwards Waeco cable fitted on vehicles like Baileys to a single 4 pin socket/plug like we use on our single camera systems. Both front and rear adaptors are provided. These cables are not made by Waeco, just compatible.  We only sell these as pairs because we have found the inside of the cables to be wired in differently, so you may not be able to just plug in one side and replace just one part, you would need to replace both monitor and camera.

These cable adaptors will convert the 2010 onwards Waeco cable fitted on vehicles like Baileys to twin 4 pin sockets/plugs like we use on the twin camera systems. Both front and rear adaptors are provided.

If you see a DC power socket on a reversing camera or a monitor, probably around 99% of the time this will be a 2.1mm/5.5mm DC socket. In some circumstances you may wish to extend this cable, for example when you wish to run an RCA/Phono based camera whilst driving by taking an ignition based power supply from the front of the vehicle back to the reversing camera. This is one of our shorter length cables at 150cm, so it is probably more commonly used to extend the reversing light power supply cable from a high up position down to the rear light cluster.

If you see a DC power socket on a reversing camera or a monitor, probably around 99% of the time this will be a 2.1mm/5.5mm DC socket. In some circumstances you may wish to extend this cable, for example when you wish to run an RCA/Phono based camera whilst driving by taking an ignition based power supply from the front of the vehicle back to the reversing camera. This is our shorter length cables at 500cm version.

If you see a DC power socket on a reversing camera or a monitor, probably around 99% of the time this will be a 2.1mm/5.5mm DC socket. In some circumstances you may wish to extend this cable, for example when you wish to run an RCA/Phono based camera whilst driving by taking an ignition based power supply from the front of the vehicle back to the reversing camera. This is our shorter length cables at 1000cm (10M) version.

If you see a DC power socket on a reversing camera or a monitor, probably around 99% of the time this will be a 2.1mm/5.5mm DC socket. In some circumstances you may wish to extend this cable, for example when you wish to run an RCA/Phono based camera whilst driving by taking an ignition based power supply from the front of the vehicle back to the reversing camera. This is our shorter length cables at 1500cm (15M) version.

Sometimes you wish to split one power supply cable so that it powers two separate devices eg a monitor and an MDVR, or two phono/RCA based reversing cameras. This cable allows you to do so.

Sometimes you wish to split one power supply cable so that it powers four separate devices eg four phono/RCA based reversing cameras. This cable allows you to do so.

We have instances of people using a 24V vehicle with a Phono RCA based cameras and cables. In these circumstances, you would require a dropper for the camera supply to regulate the output for the camera down to 12V. We also sell these to people that want to protect their phono cameras from any voltage fluctuations on 12V systems. These are only suitable for powering a camera and not a complete system (all of our premium systems have voltage regulators built-in already).

99% of the time, if you see a DC socket on a reversing camera or monitor, it will be a 2.1mm/5.5mm connector.  This wire allows you to provide power to this type of socket, and has an inline 3 amp fuse on the red input wire. Total length of this power adaptor is 150CM.

This is a 3 amp fused 2.1mm/5.5mm DC socket with 100cm red (+12/24V) and black (earth) wire attached. This is used in instances where you have bare red/black wires that you wish to connect one of our extensive range of adaptors with DC plugs to.

On agricultural machinery, there is often a 3-pin power socket, sometimes referred to as a "D-Plug" due to the shape of the connector. This power lead has been designed to plug into this and provides a 2.1mm/5.5mm DC plug that can be inserted into most of our reversing camera monitors. 

On some vans, where the doors are particularly thick it may obscure the vision of our roof mount camera (the plastic camera we sell for the roof which has a ball camera at the end). These stainless steel plates were made so you could extend the camera out further to give a better viewing angle.

This is the 5 pin version adaptor for the Fendt Vario - designed to be plugged in to the connection at the back of the arm rest converting it to a 4 pin "aviation" connector (as seen on almost all reversing cameras nowadays - including all of our selection).

These adaptors are 100cm in length. We have various extensions that will plug in to extend this adaptor, and a wide range of cameras that can be used.

We very often get people who have an older system that has unusual connectors that wish to adapt their existing wiring to the industry standard - 4 pin aviation connector.  In the past, our customers used to purchase a 1M cable, which they would cut in half to connect each wire to their existing lead.  We decided to get our cable factory to make us a new 100cm length lead which has been pre-separated out to the individual wires.  

• Adaptor R 1-camera BNC lead for Case IH AFS Pro and New Holland IntelliView displays
• Connects 1x 4-pin screw connector cameras directly to OEM monitor
• Compatible with AFS Pro 200/300/700 & IntelliView II/III/IV
• Simple plug-and-play installation

• Adaptor R 3-camera lead for Case IH AFS Pro and New Holland IntelliView displays
• Connect up to three 4-pin screw connector cameras directly to OEM monitor
• Fits 26-pin socket on rear of display + BNC port
• Compatible with AFS Pro 200/300/700 & IntelliView II/III/IV
• Simple plug-and-play installation with labelled camera inputs

These have been used for years in the marine industry to get cables inside whilst maintaining water integrity in very tricky environments. This size is suitable for single cameras (not twin lens).

These have been used for years in the marine industry to get cables inside whilst maintaining water integrity in very tricky environments. This size is suitable for two cameras or our twin lens camera.

Adaptor cable for John Deere 6R tractors with 7-pin AMP plug, compatible with GS3 Command Center and Generation 4/5 displays.