Reversing Cameras UK Ltd - REVCAMUK, Unit 98, The Oaks, Ramsgate, Kent, CT12 5FS, United Kingdom
mail@parkingcameras.com 01843863566 08006126816
Bullet/Bumper Reversing Camera Kit with Mirror Monitor | PM34
Availability
16 item(s) available
Weight
2.50 kg
Product Code:
KIT-PM34
Price:
£180.00 VAT Included
£30.00
PM34 - 7 inch mirror monitor and flush fitting bumper reversing camera kit
This reversing camera kit comes with the mirror monitor. You may choose either the clip-over existing mirror version, which has strong spring loaded clamps that will secure it to your existing interior mirror, or attach directly to the windscreen with one of our bracket options (see description below for details on choosing the right bracket).
This kit is supplied with a flush-fitting bumper reverse camera, usually fitted in the bumper but can be mounted anywhere that you can reach the rear to tighten the securing ring up.
Choice of image sensor from : 1/3" Sony CCD (90 degree lens), or a 1/2.7" CMOS 2399 1080P AHD (95 degree lens).
The reversing camera is fitted with built-in with IR LEDs to provide a good image in low light levels.
The camera is supplied with the correct sized hole saw for the camera body (28mm) to facilitate an easy installation.
The camera has a threaded body, it is supplied with angled rings and spacer rings that fit behind the bumper/body to make tightening up from the back a bit easier, plus a slight adjustment if using the angled rings (one on outside, corresponding one on inside).
IP68 Waterproof - Sometimes bumper cameras have a bad reputation for leaking, but not this camera. We have stocked this model from the same supplier for numerous years with no issues. We believe this is because this camera is constructed with mechanical seals versus applying sealant (common elsewhere). Please kindly note that on the Sony CCD option there is an inline voltage regulator on the cable that should be kept dry, if you aren't able to get this somewhere protected, please select the AHD upgrade version.
See below for information about the option choices above in the drop-down menus
Cable Length Options
We stock a large range of cable lengths to suit any vehicle, whether you have a car, van, motorhome, tractor, coach, bus, or HGV. We also stock adaptors for the Dometic/Waeco 6 pin screw locking cable commonly found pre-fitted on Burstner and Baileys motorhomes. We can also provide a slimline 8mm disconnect point to our 10M/12.5M/15M cable lengths to help you run the cable through tight gaps without having to drill a large hole for the main connector.
Power Options
On the monitor wiring harness is a 2.1mm DC socket. On the drop down menu of this product, you can select your desired power lead to plug in to this.
The standard hardwiring is supplied with all options, this terminates in a red wire (+12V/+24V), and black wire (earth).
For the ultimate quick install is a lighter plug option. Some people also order this just for the initial setup, before changing to the standard hardwiring/fuse tap.
Fuse taps aka piggyback fuse holders, are the most recent addition to our options. This allows you to "piggyback" off an existing circuit from your fuse box. The most common size fuse found in modern vehicles is the mini blade (size = 10.9mm wide x 16.4mm tall), older vehicles are likely to have the standard blade (size = 19.1mm wide x 18.8mm tall). Download and read our Fuse Tap installation instructions PDF for more information.
Our fuse taps were designed by us, they have a 200cm lead that connects directly to the monitor socket with no soldering / crimping required. There is a black wire with an earth terminal attached - designed to fix to a chassis bolt/screw. This earth wire/terminal can be separated away from the red wire to enable you to find the most convenient ground/earth (although often this is next to the fuse box).
Image Sensor Options
An image sensor is the part of a camera that collects colour and light detail from the lens and turn it in to a signal that will be sent to the monitor display. The image sensor has one of the largest impacts on picture quality. We offer 2 choices of image sensor (1x high resolution and 1x high definition), if you select the high definition option you will also receive an upgraded spec monitor. The 3 choices are listed below :
Sony 1/3" 600tvl CCD - Supplied with a 90 degree field of view lens, and a respected CCD image sensor by Sony.
CMOS 2399 1080P - Supplied with a 95 degree field of view lens, using a high definition 1080P AHD image sensor. This option also means your monitor is upgraded to an IPS panel with an even higher definition.
For many years we have supplied the universal clip-over existing interior mirror rear-view monitor. More recently we have also begun to offer the monitor with a variety of direct-to-windscreen stalk brackets. We have windscreen brackets to fit the most popular van and motorhome models, as well as a universal option where you can glue a mounting plate to the windscreen for a bracket to fit. See our guide below for more information about the different bracket options.
Some popular van models are listed below with the bracket options we commonly see. This is a rough guide, and we have seen lots of variation. If in doubt, Email Us a clear photo of what you have fitted to your windscreen.
We have been using this type of cabling since 2007, and it has performed perfectly in all of this time. It is called the 4 pin aviation cable, and uses what is known as a 4 pin GX12 connector.
This type of connector is very durable, and can be kept outside exposed to rain and freezing temperatures.
It makes fitting easier, and avoids CANBUS issues due to the monitor powering the camera.
It keeps contacts clean and dry, plus prevents them from accidental separation.
It has become the industry standard connector, which means you aren't forced to buy future cameras/cables/upgrades from one retailer - as parts are interchangeable between numerous suppliers (although we are confident you will be impressed enough with us that you will choose us for any future upgrades/spare parts).
All of our aviation extension cables are high quality, with the inner cores consisting of pure copper. We do not use the cheaper CCA (Copper Coated Aluminium) or CCS (Copper Coated Steel) cables, because they are more prone to failure/degradation over time.
2 Year Guarantee
We supply with a 2-year Guarantee with us, meaning we will repair or replace any non-user damaged parts that are deemed faulty. Our failure rate is very low even beyond these two years, if you have a problem outside of 2 years we should still have compatible parts and possible repairs for reasonable amounts.
Parts Tested in the UK
The parts of this kit will have been tested twice, once by the factory and once by us. We check all the items in the kit including all cables, trigger wires, IR LEDs and menu functions to reduce any chance of having a non-working part. Our fault rate is extremely low, and we just like to ensure that we avoid any imperfection slipping past. This is why professional fitters love us.
Information correct as of 14:52, Wednesday, January 7, 2026
